Frenos de aire — examen de práctica 2026

IncorrectoRespuesta correcta: B — At the end of every working day

Contamination builds up every time the compressor runs, so on a manually drained system the tanks have to be emptied at the close of each day's work. Waiting for a warning or for the next shop visit lets that build-up sit in the tanks for weeks.

Treating tank draining as a maintenance-shop chore on a monthly cycle rather than a daily driver duty, which lets contamination build up until valves stick.

IncorrectoRespuesta correcta: C — Keep moving in a low gear and drag the brakes gently until friction heat drives the water out

Gentle applications while the vehicle is moving generate the friction heat needed to boil the water out of the linings, and a low gear keeps the vehicle slow and controllable while that is happening. Setting the parking brake on soaked brakes risks freezing them in place in cold weather instead of drying them.

Believing wet brakes recover on their own with time, or that the parking brake is a safe way to dry them, when in freezing conditions it can lock the vehicle where it stands.

IncorrectoRespuesta correcta: B — Let speed reach 45, brake firmly until you are down to about 40, release completely, and repeat once you are back at 45

Firm, short applications of roughly three seconds put heat in and then give the drums time to shed it while the brakes are fully released, and each application should take about five mph off your safe speed. Constant light pressure never lets them cool, which is precisely how linings and drums are heated into fade.

The intuition that gentle continuous pressure is easier on the brakes than firm intermittent pressure, when the opposite is true because cooling only happens during release.

IncorrectoRespuesta correcta: A — Heat, and too much of it makes the brakes stop working

Braking converts motion into heat. A drum can only absorb so much before the brakes fade, and how much depends on how hard and how long they have been used — which is why a long descent is handled with gearing rather than steady pedal pressure.

Thinking of brake failure as purely mechanical breakage, when the usual cause on a grade is simply too much accumulated heat.

IncorrectoRespuesta correcta: B — An electric switch operated by air pressure when you brake

Applying the brakes raises air pressure in the line, and that pressure closes an electrical switch that lights the brake lamps. It is worth knowing because a fault there leaves you slowing with no warning to the traffic behind.

Assuming the brake lights are wired to the pedal itself, as in a car, rather than to the air pressure the pedal creates.

IncorrectoRespuesta correcta: B — Something is wrong and a mechanic needs to look at it

The valve is a last defence against over-pressure, typically opening around 150 psi. A properly governed system never reaches that point, so a venting safety valve is evidence of a fault, not of normal operation.

Hearing the release as the routine sound of a system topping up, when the governor should have stopped the compressor long before this valve opens.

IncorrectoRespuesta correcta: A — Check the certification label for the build date, or look underneath for the control unit and sensor wiring

ABS became a requirement for air-braked trailers and dollies built from March 1998 onward, and for air-braked truck tractors a year earlier. On an older unit, the manufacture date on the certification label settles it, and the electronic control unit with its wheel speed sensor wires is visible from below.

Assuming universal fitment. Plenty of pre-requirement equipment is still in service, and some of it was voluntarily equipped while some was not.

IncorrectoRespuesta correcta: B — 100 psi in both the primary and secondary systems

A dual system is two independent circuits sharing one set of controls, and both need working pressure before you move. Setting off with one circuit low means part of the vehicle's brakes are not doing their share.

Watching only one gauge or needle and treating the vehicle as ready when that one is satisfied.

IncorrectoRespuesta correcta: B — About 32 feet

During the fraction of a second the air takes to reach the brakes, the vehicle is still rolling at full speed. At 55 mph that untouched roll works out to roughly 32 additional feet before any slowing begins.

Treating brake lag as negligible because it is under a second, ignoring that at highway speed even a half second covers most of a truck length.

IncorrectoRespuesta correcta: C — Normal, because front wheel braking helps in all conditions

The valve was meant to prevent front wheel skids, but it cuts your stopping power to do it, and testing showed those skids are unlikely even on ice. Leaving it in the normal position keeps the front brakes doing their share.

Trusting the label: "slippery" sounds like the setting for a slippery road, but using it there costs braking without buying safety.

IncorrectoRespuesta correcta: C — You may have lost ABS on one or more wheels, but the normal brakes still work

ABS sits on top of the normal braking system. Losing it costs you the anti-lock function at one or more wheels, but the brakes themselves are unaffected — you have ordinary brakes and should have the fault repaired.

Treating an ABS light as a total brake failure, or at the other extreme as a light that can be ignored indefinitely.

IncorrectoRespuesta correcta: B — 20 to 45 psi

The springs take over well below the warning threshold, most often somewhere in the twenties or thirties. That gap exists so a driver who reacts to the warning can park deliberately rather than being stopped by the vehicle.

Believing the spring brakes apply at the same pressure that triggers the warning light, which would leave no reaction time at all.

IncorrectoRespuesta correcta: B — The brakes are fading, and you should slow down and take a lower gear

Needing more pressure for the same result means the brakes are giving less for each application — the signature of fade, though air leaks, mechanical faults or brakes out of adjustment can produce it too. Either way the answer is less speed and more engine braking.

Reading rising application pressure as the system working harder on your behalf, rather than as evidence it is losing effectiveness.

IncorrectoRespuesta correcta: C — Each release lets air out, and you can lose pressure faster than the compressor replaces it

Every time the pedal comes up, some compressed air leaves the system. Fanning the pedal repeatedly can drain the tanks faster than the compressor refills them, and the brakes fail when pressure gets low enough.

Carrying over the habit of pumping brakes from a car with hydraulic brakes, where nothing is consumed by repeated application.

IncorrectoRespuesta correcta: C — There is only enough air for a few releases, so plan where you are going first

The reserve tank exists to move a vehicle out of danger, not to keep it in service. Each release spends part of a small supply, so a driver who moves without a plan can run out somewhere worse than where they started.

Treating the emergency release as a working air supply, which turns a bad parking spot into a stalled vehicle in traffic.

IncorrectoRespuesta correcta: A — 55 psi

The warning has to appear while you still have enough air to make a controlled stop. 55 psi is the threshold on a typical vehicle; the spring brakes will not grab until pressure falls much further, which is exactly the margin the warning is protecting.

Confusing the warning threshold with the pressure at which spring brakes apply on their own — those are two different numbers, and the gap between them is your time to pull over.

IncorrectoRespuesta correcta: B — The loss is too great; a combination may not lose more than 4 psi in that minute

Holding the pedal down pressurizes the service side as well, so the limit rises slightly, to 3 psi for a single vehicle and 4 psi for a combination. A 5 psi drop exceeds that, meaning a leak that must be found and repaired before the vehicle moves, or air can run out on the road.

Rationalizing a slightly excessive drop as normal for an older combination, when the whole point of the timed test is that the threshold is fixed.

IncorrectoRespuesta correcta: A — Less than 2 psi for a single vehicle and less than 3 psi for a combination

With no brake applied, only the supply side is pressurized, so the allowable loss is the tighter of the two limits. A combination gets one extra psi because it has more lines, couplers, and chambers holding air.

Mixing up the no-application limits with the higher limits that apply when the foot brake is held down, which lets a genuinely leaky vehicle pass the test.

IncorrectoRespuesta correcta: B — Once the wheels are turning again, which may take close to a full second after the release

A locked wheel provides no directional control, and it does not begin turning the instant the pedal comes up. Waiting for the wheels to roll is what lets the vehicle straighten out; re-applying while they are still sliding just relocks them and the rig stays crooked.

Reapplying instantly because any pause feels like lost stopping distance, which defeats the entire purpose of the release phase.

IncorrectoRespuesta correcta: B — The drum grows in diameter, so the shoes meet it later in their travel and squeeze it more weakly

Metal expands when hot, so the friction surface moves away from the shoes. The chamber pushrod has a fixed amount of travel, and spending more of it just reaching the drum leaves less to squeeze with, so the same pedal effort produces a weaker application.

Picturing fade as purely a slippery-lining problem, which hides the geometric half of the failure and why fade gets worse the longer the grade runs.

IncorrectoRespuesta correcta: A — Within 45 seconds

A dual system has to replenish air fast enough to keep up with repeated brake applications. If buildup is slow, pressure can fall away during driving and force an emergency stop, so a vehicle failing this check should not be driven. Larger than minimum tanks can legitimately take longer, per the manufacturer.

Applying the old single-system standard of 50 to 90 psi in three minutes to a modern dual system, which would let a badly weakened compressor pass.

IncorrectoRespuesta correcta: A — Park on level ground, chock the wheels, and let the brakes cool before setting the parking brakes

Clamping very hot brakes can damage them with the trapped heat. Chocks on level ground hold the vehicle mechanically while the drums cool, and the parking brakes go on once the heat has come out of them. Never leave the vehicle held by nothing at all.

Assuming the parking brake is always the right answer for holding a vehicle, without recognizing the two conditions, very hot brakes and very wet brakes in freezing weather, where it causes damage.

IncorrectoRespuesta correcta: C — Because modulated braking lasts only as long as the air already in the tanks, and the spring brakes will set themselves once pressure gets low enough

The warning means air is leaving faster than it is being made. You can meter the brakes only while tank air lasts; once pressure falls into the low range the spring brakes set with no pedal control, and because they do not act on every axle a loaded vehicle travels far while a light one or a slick road can skid it out of control.

Treating spring brakes as an emergency backup that will stop the vehicle safely, rather than an uncontrolled application that happens at a moment of the leak's choosing.

IncorrectoRespuesta correcta: C — Only when every axle of the vehicle, or of the entire combination, carries a functioning antilock system

Full pedal is safe only when every wheel has a system preventing it from locking. With antilock protection working everywhere, the computer holds the wheels short of lockup; anywhere else, mashing the pedal locks wheels and costs steering.

The belief that an emergency always justifies standing on the pedal, and the related error that dry pavement or a light load makes lockup impossible. Empty rigs actually lock up more easily.

IncorrectoRespuesta correcta: B — Ease off the brakes, if it is safe to do so, until you regain control

Trailer ABS protects the trailer wheels only; the unprotected tractor wheels are the ones locking and swinging the cab. Releasing enough pressure lets those wheels roll again, and a rolling wheel is the only wheel that can steer or resist the jackknife.

Assuming ABS anywhere on the combination protects the whole combination, so the driver stays on the pedal while the unprotected axles are already sliding.